MCP Supporting Windows 95
  1. Ποιες εντολές πρέπει να υπάρχουν στο Config.sys και ποιες στο AUTOEXEC.BAT για την υποστήριξη Ελληνικών χαρακτήρων στο MS-DOS;
    CONFIG.SYS
    device=c:\windows\command\display.sys con=(ega,,1)
    country=030,737,c:\windows\command\country.sys
    AUTOEXEC.BAT
    mode con codepage prepare = ((737) c:\windows\command\ega2.cpi)
    mode con codepage select = 737
    Keyb gk,,c:\windows\command\keybrd4.sys
  2. Ποιες είναι οι απαιτήσεις σε σύστημα για την εκτέλεση των Windows 95;
    386DX/20Mhz, 4Mb RAM 8Mb recommended for Microsoft Exchange,
    MS-DOS 3.2 or higher, HHD with free space listed in the table below:
    New Installation 30 – 40Mb
    Upgrade over Windows 3.1 20 – 30Mb
    Upgrade over WFW10 – 20Mb
    +6Mb for system files backup (when install over existing windows)
    +14Mb for swap file.
  3. Ποιες οι απαιτήσεις του προγράμματος SETUP;
    MS-DOS 3.2 (support partitioning >32Mb)
    Windows 3.1 or Windows For Workgroups
    Dual boot OS/2 with MS-DOS
    Dual boot Windows NT with MS-DOS
    417Kb Conventional memory
  4. Ποιοι οι διακόπτες του προγράματος SETUP και τι κάνει ο καθένας σε εκτέλεση από MS-DOS και Windows.
    MS-DOS switches
    /IS= Disables scandisk from running at the beginning of setup.
    /ID= Does not check for disk space.
    /IM= Ignores conventional memory check.
    /IL= Installs Logitech series C mouse driver.
    /IQ= Disables cross-link hard disk check (if /IS is used).
    /C= Do not load SmartDrv.
    /T:<path>= Specifies the folder where SETUP copies temporary files.
    <Batch Filename>= Specifies the batch file that contains SETUP options.
    /?= Help
    Windows switches
    /T:<path>= Defines location for temporary SETUP files.
    /ID= Does not check for disk space.
    /IM= Ignores Conventional memory check.
    /IN= Does not run Network SETUP module.
    /IQ= Disables cross-link hard disk check (id /IS is used).
    /IS= Skips the routine system check.
    /?= Help.
  5. Ποιες είναι οι default ρυθμίσεις του συστήματος μετά την εγκατάσταση των Windows 95;
    Files60
    Buffers30
    FCBS4
    Stacks9,256
    DOSHigh,UMB,Auto
  6. Ποια αρχεία παλαιότερης έκδοσης, πρέπει να κρατηθούν backup, προκειμένου να εγκαταστήσετε τα Windows 95;
    *.INI
    *.PWL
    *.GRP
    *.DAT
    CONFIG.SYS, AUTOEXEC.BAT
    Network configuration files, login scripts
  7. Ποια είναι τα στάδια της διαδικασίας SETUP;
    Real-Mode
    a.Run Scandisk
    b.System check.
    c.Check if windows exists
    d.XMS? – Load cache.
    e.TSR?
    f.Load Windows portions of SETUP
    Protected-Mode
    g.Protected mode.
    h.User input.
    i.Hardware detect.
    j.Copy files.
    k.Modify boot record.
    l.Restart.
    m.First time run.
  8. Σε ποιο κλειδί της Registry πρέπει να αναφερθούμε όταν εκτελούνται λάθος προγράμματα κατά την εκκίνηση των Windows 95;
    Hkey_Current_User\Software\Microsoft\Windows\CurrentVersion\Explorer\Shell Folders
    The value Startup= should be Windows\Start Menu\Programs\Startup
  9. Σε ποια κλειδιά της Registry πρέπει να αναφερθούμε όταν εκτελούνται προγράμματα που δεν επιθυμούμε τα οποία φορτώνονται στο system tray κατά την εκκίνηση των Windows 95;
    Hkey_Current_User\Software\Microsoft\Windows\CurrentVersion\Run
    Hkey_Local_Machine\Software\Microsoft\Windows\CurrentVersion\Run
  10. Ποιες δηλώσεις μπορούν να συνταχθούν στο αρχείο Msdos.sys στο τμήμα [Options];
    BootDelay=nSets the initial startup delay to n seconds.
    BootFailSafe=Enables Safe Mode for system startup.
    BootGUI=Enables automatic graphical startup into Windows 95.
    BootKeys=Enables the startup option keys (F5, F6, F8).
    BootMenu=Enables automatic display of the Windows 95 startup menu.
    BootMenuDefault=#Sets the default menu item on Windows 95 startup menu.
    BootMenuDelay=#Sets the number of seconds to display the Windows 95 startup menu.
    BootMulti=Enables dual boot capabilities.
    BootWarn=Enables Safe Mode startup warning.
    BootWin=Enables Windows 95 as the default operating system.
    DblSpace=Enables automatic loading of DblSpace.Bin.
    DoubleBuffer=Enables loading of double buffering driver for SCSI controler.
    DrvSpace=Enables automatic loading of DRVSPACE.BIN.
    LoadTop=Enables loading COMMAND.COM at top of 640K. memory.
    Logo=Enables display of animated Logo.
    NetWork=Enables Safe Mode With Networking as a menu option.
  11. Αναφέρετε του διακόπτες του EXPLORER και τι κάνει ο καθένας;
    /n= Opens a new single pane window.
    /e= Opens a new double pane window.
    /root, <object>= Sets the root for a view.
    /select, <object>= Selects an object in the current view.
  12. Ποια είναι η χρησιμότητα του SNAPSHOT.EXE, ποιοι οι διακόπτες που δέχεται και τι κάνει ο καθένας.
    The SNAPSHOT.EXE utility is called in AUTOEXEC.BAT is real-mode programm that prepares for the transition to protected–mode networking. A protected-mode counterpart SNAPSHOT.VXD stored in the shared Windows\SYSTEM directory uses this information to load protected-mode network client.
    /B:nSets n as the boot drive.
    /M:nSets the amount of memory to reserve for real-mode network.
    /SEnables shut down trapping.
    /RIndicates that this is a diskless workstation.
    /VSets verbose mode.
  13. Ποια η χρησιμότητα της εντολής SETMDIR ποιους διακόπτες αναγνωρίζει και τι κάνει ο καθένας;
    The SETMDIR command is used to set the machine directory for the computer and load the full Registry.
    /VSets verbose mode.
    /R:pathSets the current Registry and environment variables to the specified path.
  14. Ποια είναι η δομή των Windows 95 και τι εκτελέιται σε κάθε τμήμα αυτής της δομής;
    Ring 0Components protected by processor architecture. (Drivers and critical OS functions).
    Ring 1,2Not used.
    Ring 3Components protected by operating system. (User and OS API Calls).
  15. Ποια τα περιεχόμενα της system Virtual Machine;
    a.Base system components (Kernel, User, GDI).
    b.An address space shared for 16bit Windows programs.
    c.A separate address space for each 32bit Windows program.
  16. Αναφέρετε τα βασικά δομικά στοιχεία του λειτουργικού και τι κάνει το καθένα;
    a.     KERNEL.DLL
    Handles the base operating system functions such as memory management, file I/O, program loading and execution.
    b. USER.DLL – USER.EXE
    Control user input and output, including the keyboard, mouse, sound driver, timer, communication ports.
    c. GDI32.DLL – GDI.EXE
    Manage graphics and printing. This includes turning pixels on/off, drawing graphics on screen or printer.
    d. WinNet
    The WinNet DLL’s allow device-independent access to Network functions.
    e. Multimedia
    Handles the interface for multimedia device drivers and I/O functions. This includes compression and decompression algorithms and synchronizing audio with video.
  17. Πόσων ειδών drivers μπορούν να επεξεργαστούν τα Windows 95;
    MS-DOS real-mode drivers *.SYS
    Real-mode Windows drivers (usually listed in system.ini) *.DRV
    Protected-mode Windows 95 drivers (virtual drivers) *.VxD or *.386
  18. Ποια κλειδιά διαθέτει η Registry και τι πληροφορίες κρατά το καθένα;
    a. Hkey_Classes_Root
    This key contains the same type of data as the REG.DAT did in Windows 3.x. This is information about OLE and file association mappings.
    b. Hkey_Current_User
    This key contains user specific information about system and programs. This key is created every time user logs form information loaded from Hkey_Users.
    c. Hkey_Local_Machine
    Contains specifications for the computer, drivers and other system settings. This is machine specific information about the type of hardware installed, how ports are mapped out and how the software is currently configured.
    d. Hkey_Users
    Contains information about all the users of this workstation. The information contained concerns the various default setting for programs, event schemes, desktop configuration and so on.
    e. Hkey_Current_Config
    Contains information about the current configuration or the hardware attached to the computer. This key is mainly used if there are multiple configurations available to the computer and the data is loaded from Hkey_Local_Machine.
    f. Hkey_Dyn_Data
    Contains dynamic status information for various devices. The information in this key is regenerated every time system starts up. This key is apart odf the performance measuring information and also for Plug &Play configuration. Also contains data on system monitoring being performed by the System Monitor Tool.
  19. Με ποιο πρόγραμμα μπορούμε να κάνουμε αλλαγές στη Registry ποιους διακόπτες δέχεται και τι κάνει ο καθένας;
    REGEDIT.EXE, Registry editor can be used to view or modify the Registry on a local computer or on another computer over a network.
    /L:systemSpecifies the location of system.dat
    /R:userSpecifies the location of the USER.DAT
    file.regSpecifies the reg file to be imported into the Registry.
    /e file.regSpecifies the filename to which the Registry should be exported.
    RegkeyOptional, specifies the starting Registry Key from which to export a portion of Registry.
    /c file.regSpecifies the reg file to use to replace the entire contents of the Registry.
  20. Ποια είναι τα πλεονεκτήματα από τη χρήση το Client For Microsoft Networks;
    a. High performance using no conventional memory.
    b. Protected-mode peer resource sharing services.
    c. Security and other support on Windows NT Networks.
  21. Τι κοινό θα πρέπει να έχουν υπολογιστές που τρέχουν Microsoft Networking products έτσι ώστε να μπορούν να μοιράσουν resources;
    Must be running a common protocol.
  22. Ποιο είδος security είναι διαθέσιμο στα peer-to-peer Networks;
    Share level security.
  23. Τι είδους security πρέπει να διαθέτει το δίκτυο έτσι ώστε να μπορούμε να χρησιμοποιήσουμε τις περισσότερες δυνατότητες του remote administration;
    User level security, which requires a server running Windows NT or NetWare to provide pass through authentication of users.
  24. Τι ενέργεις πρέπει να εκτελεστούν προκειμένου νεα εγκαταστήσετε το Client For Microsoft Networks;
    a. In the Network option in Control Panel click Add button.
    b. In the Select Network Component Type dialog box, double click Client.
    c. In the Select Network Client dialog box, click Microsoft in the manufacturers list, and click Client For Microsoft Networks in the Network Clients list.
  25. Με ποιο τρόπο μπορούμε να θέσουμ ε το Client For Microsoft Networks σαν πρωτεύον Client του δικτύου;
    a. In then Network option, in Control Panel, click Configuration tab.
    b. In the Primary Network Logon list, click Client For Microsoft Networks.
  26. Τι προϋπόθεση πρέπει να ισχύει για να μπορούν οι υπολογιστές που τρέχουν Windows 95 να προβάλουν τα resources ενός LANManager server;
    At least one computer running Client For Microsoft Networks sets its Workgroup Name to the LANManager Domain.
  27. Ποιες προύποθέσεις πρέπει να ισχύουν για να μπορούν υπολογιστές που τρέχουν LANManager να προβάλουν τα resources υπολογιστών που τρέχουν File And Printer Sharing For Microsoft Networks;
    a. Make sure that all computers are using a common protocol.
    b. Make sure that users running LANManager clients have been granted access to the resources on the computers running Windows 95.
    c. Set the value of thw LM Announce property to Yes on each computer running Windows 95 with File And Printer Sharing services.
  28. Σε ποιο αρχείο αποθηκεύονται οι παράμετροι για το real-mode networking;
    PROTOCOL.INI
  29. Ποια είναι τα πλεονεκτήματα από τη χρήση του Microsoft Client For NetWare Networks για σύνδεση σε δίκτυα Novell;
    a. A high preformance system using no conventional memory.
    b. Protected-mode peer resource sharing services.
    c. Interoperation and Logon with NetWare 2.15, 3.x and 4.x servers.
    d. Support for packet-burst protocol for faster data transfer.
    e. Automatic reconnection for lost server connection.
    f. Large Internetwork packet (LIP) protocol support.
    g. Support for all documented MS-DOS and NetWare API’s defined by Novell.
    h. Enhanced performance and new networking features. (plug&play support, remote network access, user profiles for system configuration, long filenames on NetWare 3.x and 4.x volumes configured to use the OS/2 name space).
  30. Ποια είναι τα πλεονεκτήματα από τη χρήση του Client που δίνεται από τη Novell;
    a. Improved network adapter driver support.
    b. Protected-mode IPX/SPX compatible protocol.
    c. Compatibility with native NetWare services and commands.
  31. Σε ποιες περιπτώσεις ΔΕΝ πρέπει να χρησιμοποιούμε το Client For NetWare Networks;
    a. To take advantage of NetWare NCP packet signature for enhanced protection of servers and client computers using NCP.
    b. If your site needs to use NetWare IP, you should use NETX or VLM.
    c. If you use 3270 emulators that rely on DOS-helper TSR’s or need 3270 emulation for applications in MS-DOS sessions.
    d. If you are using custom VLM components such as PNW or Novell utilities such as NWADMIN or NETADMIN.
    e. If your site needs to use NetWare directory services NDS, you should use VLM.
  32. Σε ποιες περιπτώσεις ΔΕΝ πρέπει να χρησιμοποιούμε τον Client Που δίνεται από τη Novell, αλλά το Client For NetWare Networks;
    a. If you want the performance advantages of 32bit, protected-mode network clients and network adapter drivers, including complete PnP support.
    b. If you want to take advantage of the Windows 95 unified Logon and user Interface for navigating the network, plus the Windows 95 network management tools.
    c. If you want to take advantage of long filenames, automatic reconnection and other performance enhancements.
    d. If you want to take advantage of use profiles to manage desktop configurations.
    e. If you want to take advantage of Windows 95 peer resource sharing without running another network client.
  33. Ποιες ενέργεις πρέπει να κάνουμε, προκειμένου να εγκαταστήσουμε τα source files των Windows 95 σε ένα NetWare server.
    a. On the network Administrator’s computer logon to the NetWare file server where you want to place the Windows 95 source files.
    b. On the Administrator’s computer, run castoff all to ensure that server-to-workstation or workstation-to-workstation messages do not affect SETUP.
    c. Follow the procedures for copying the Windows 95 source files to a server.
  34. Τι πρέπει να κάνουμε προκειμένου να ενεργοποιήσουμε την υποστήριξη Long filenames σε έναν NetWare server;
    a. At the NetWare server console prompt, type the following lines:
    Load os2
    add name space os2 to volume sys
    b. Add the following line to STARTUP.CNF file:
    Load os2
    c. Shut down the file server. Then copy the file os2.nam from NetWare distribution disks or compact disk to the same disk and directory that contains SERVER.EXE on the NetWare file server.
    d. Restart the NetWare file server.
  35. Σε περίπτωση που αντιμετωπίζουμε πρόβλημα με τα Long filenames παρόλο που έχει εγκατασταθεί η υποστήριξη τέτοιων ονομάτων στον NetWare server, τι ενέργειες μπορούμε να κάνουμε στους υπολογιστές που τρέχουν Windows 95, έτσι ώστε να λυθεί το πρόβλημα;
    In the Registry Key:
    Hkey_Local_Machine\System\CurrentCon    trolSet\Services\VxD\Nwredir
    setting supportLFN=
    0= LFN not supported by NetWare server.
    1= (default), LFN’s supported by NetWare server.
    2= LFN’s supported if NetWare server supoports LFN’s.
  36. Που αποθηκεύονται τα user profiles στον NetWare server, ποιο είναι το αρχείο που κρατά τα User profiles και ποιο των system policies;
    User profiles stored in USER.MAN in MAIL directory on NetWare server.
    System policies stored in CONFIG.POL in SYS:PUBLIC directory on NetWare server.
  37. Σε ποιες περιπτώσεις το SETUP των Windows 95 δεν εγκαθιστά αυτόματα τον Microsoft Client For NetWare Networks;
    a. The computer is using VLM with NetWare 4.x NDS.
    b. Certain TSR’s are present that require ODI.
    c. Certain TSR’s are present that are not compatible with protected-mode client, but can use the new implementation of the IPX/SPX compatible protocol.
    d. Certain TSR’s are present that are not compatible with Client For NetWare Networks or other protected-mode components.
  38. Ποιες ενέργειες μπορεί να εκτελέσει το SETUP των Windows 95 προκειμένου να εγκαταστήσει το Client For NetWare Networks και τα άλλα protected mode components;
    a. Comment out NetWare-related TSR’s in AUTOEXEC.BAT that are not required.
    b. Move certain TSR’s from AUTOEXEC.BAT to WINSTART.BAT so that this software can be loaded at the appropriate time during system startup.
    c. Install new 32bit, protected mode versions of networking components such as protocols and Network adapter drivers.
    d. Comment out entries from SYSTEM.INI that are not required when using protected-mode networking components.
    e. Configure settings in Registry related to support for NetWare networks.
  39. Σε ποιο αρχείο βρίσκονται καταχωρημένες οι πληροφορίες σχετικά με τις ενέργειες που πρέπει να εκτελέσει το SETUP των Windows 95 προκειμένου να εγκαταστήσει τα networking components;
    Installation actions are defined in NETDET.INI.
  40. Ποιες ενέργειες πρέπει να κάνουμε προκειμένου να εγκαταστήσουμε το Client For NetWare Networks;
    a. In the Network option in Control panel, examine the list of installed components and remove NetWare Workstation Shell if it is present.
    b. Click Add, and then double click Client in the Select Network Components dialog box.
    c. In the Select Network Components dialog box, click Microsoft in the Manufacturers list and then click Client For NetWare Networks. Then Click OK.
  41. Πως ενεργοποιούμε έναν 32bit protected-mode network adapter driver;
    a. In the Network option in Control panel, double click the Network adapter in the list of installed components.
    b. In the properties for the adapter, click Driver Type tab.
    c. Click the option named Enhanced Mode (32bit and 16bit) NDIS driver and click OK. Then shut down and restart the computer.
  42. Ποια είναι τα μειονεκτήματα από τη χρήση ενός ODI (Open DataLink Interface) driver σε σχέση με έναν NDIS 3.1 και το Client For NetWare Networks;
    a. There is some use of Conventional memory, and the overall performance is not as good as can be with NDIS 3.1.
    b. There is no PnP capabilities, for the networking components.
    c. You can not use this configuration to run a shared installation of Windows 95.
  43. Πιο είναι το μοναδικό προτόκολλο επικοινωνίας των Windows 95 με έναν NetWare server, και τι πρέπει να κάνουμε, προκειμένου να εγκαταστήσουμε άλλο ένα προτόκολλο για διαφορετική χρήση (π.χ σύνδεση στο Internet);
    Client For NetWare Networks is always bound only to IPX/SPX-compatible protocol. If you require an additional protocol (such as TCP/IP), you must install an additional Client such as Client For Microsoft Networks.
  44. Ποια εντολή πρέπει να υπάρχει στο CONFIG.SYS όταν χρησιμοποιούμε το File And Printer Sharing For NetWare Networks;
    Lastdrive=32
  45. Ποιο κλειδί της Registry επιρεάζει την χωρητικότητα του IPX packet Για LIP protocol και ποια τιμή πρέπει να δώσουμε προκειμένου να έχουμε τη μέγιστη χωρητικότητα;
    Hkey_local_Machine\System\CurrentControlSet\Services\VxD\Nwredir
    set the MaxLIP=0x000005DC.
  46. Τι πρέπει να κάνουμε προκειμένου να θέσουμε εκτός την υποστήριξη packet-burst protocol η οποία εξορισμού είναι ενεργοποιημένη από το File And Printer Sharing For NetWare Networks;
    In Registry at key:
    Hkey_Local_Machine\System\CurrentControlSet\Services|VxD\Nwserver
    set the SupportBurst=0.
  47. Τι πρέπει να κάνουμε έτσι ώστε να μπορούμε να τρέξουμε utilities του Novell NetWare 3.x στα Windows 95;
    a. Map a drive to the volume containing the NetWare utilities by using statement in a login script or by using the Map Network Drive dialog box.
    b. From the start button, point to Programs and then click MS-DOS prompt to start an MS-DOS session.
    c. Switch to the mapped network drive, and then run the utilities in the usual way.
  48. Ποιες ενέργειες πρέπει να γίνουν κατά τη διαδικασία του SETUP των Windows 95 προκειμένου να χρησιμοποιηθεί ο Client που δίνεται από τη Novell;
    a. Make sure that the Novell-supplied network software is running. Run the Windows 95 SETUP and select Custom Setup Type.
    b. When the Network Configuration dialog box appears, select Client For NetWare Networks and click Remove.
    c. Click Add, and then double click Client in the Select Network Component Type dialog box.
    d. In the Select Network Component Type dialog box, click Novell in the Manufacturers list and click Workstation Shell 3.x [NETX] in the Clients list. Then click OK.
    e. Click the Next button in the Network Configuration dialog box.
    f. Continue with Windows 95 SETUP.
  49. Ποιες ενέργειες πρέπει να γίνουν για να εγκατασταθεί ένας monolithic IPX driver μετά την εγκατάσταση των Windows 95;
    a. In the Network option in Control Panel, select all installed networking components and click Remove.
    b. Click Add, and then double-click Adapter in the Select Network Component Type dialog box.
    c. From the Manufacturers list in the Select Network Adapters dialog box, click Novell. Form the Network Adapters list, click Novell IPX Monolithic drivers and click OK.
    d. Shut down and restart the computer for changes to take effect.
  50. Ποια εντολή πρέπει να υπάρχει στο NET.CFG έτσι ώστε να λυθούν τυχόν προβλήματα σχετικά με την διαγραφή και προβολή των directories λόγω έληψης υποστήριξης dots (.), ή double-dots (..);
    show dots=on
  51. Αν ήδη χρησιμοποιούμε VLM με Windows 3.1 ποιες ενέργειες πρέπει να κάνουμε έτσι ώστε να συνεχίσουμε να χρησιμοποιούμε το VLM και στα Windows 95 που πρόκειται να εγκατασταθούν πάνω στα Windows 3.1;
    a. After SETUP is complete, in the Network option in Control Panel, select Client For NetWare Networks and click Remove.
    b. click Add, and then double–click Client.
    c. In the Select Network Client dialog box, click Novell in the Manufacturers list, and click the option named Novell NetWare (Workstation Shell 4.0 and above [VLM]) in the Network Clients list. Then click OK.
    d. If you want to install Client For Microsoft Networks at this time you can repeat the steps in the Select Network Client dialog box to install it. Then Shut down and restart the computer.
  52. Αν ήδη χρησιμοποιούμε VLM με Windows 3.1 η με MS-DOS και θέλουμε να εγκαταστήσουμε Windows 95 σε ένα νέο directory, ποιες ενέργειες πρέπει να κάνουμε έτσι ώστε να συνεχίσει να υπάρχει η υποστήριξη VLM;
    a. Make sure that the Novell-supplied Network is running. Run SETUP and choose Custom SETUP.
    b. When the Network Configuration dialog box appears, select Client For NetWare Networks in the list of components (if this has been installed) and then click Remove.
    c. Click Add, and then double click Client in the Select Network Component Type dialog box.
    d. In the Select Network Client dialog box, click Novell in the Manufacturers list, and click Novell NetWare (Workstation Shell 4.0 and above [VLM]) in the Network Client list. Then click OK.
    e. SETUP places information in AUTOEXEC.BAT instructs you to run the Novell Workstation Shell Install Program, after copying files phase is complete.
    f. Restart the computer again and let Windows 95 start normally.
  53. Ποιες ενέργειες πρέπει να κάνουμε για να ρυθμίσουμε το search mode στα Windows 95;
    a. From the File menu in System Policy Editor, click Open Registry. Then click the icon for Local computer.
    b. Click Network, click Microsoft Client For NetWare Networks, and then click serach-mode.
    c. Specify a setting based on the table following this procedure. Then Shut down and restart computer.
    0     ή 1 = Uses The default search mode.
    2 = Causes Client For NetWare Networks not to look in any search drives.
    3 = The same as mode 1, except that if the application has no defined directory path to search cmd open files.
    5 = Cause Client For NetWare Networks to always look in the search drives, even if application specifies path.
    7 = The same as mode 5, except that Client For NetWare Networks looks in the same drives only if the open request is a read only request.
  54. Τι πρέπει να κάνουμε αν αντιμετωπίζουμε προβλήματα με το Microsoft Client For NetWare Networks;
    Make sure that the version of NETWARE.DRV is a size about 2K. If it is much larger, remove Client For NetWare Networks and reinstall it.
  55. Τι πρέπει να κάνουμε αν δεν υπάρχει κανένα δίκτυο διαθέσιμο μετά την εκκίνηση των Windows 95, όταν χρησιμοποιούμε Client For NetWare Networks;
    a. Verify that Client For NetWare Networks is installed.
    b. Verify that IPX/SPX-compatible protocol is in the list of installed components.
  56. Τι ενέργειες πρέπει να κάνουμε αν δεν τρέχει το login script παρόλο που έχουμε εγκατεστημένο το Client For NetWare Networks;
    Make sure the correct preferred server is set and that enable login script processing is checked in the properties of the Client For NetWare Networks.
  57. Τι πρέπει να κάνουμε αν δεν μπορούν να βρεθούν οι NetWare servers όταν κάνουμε browsing το δίκτυο, χρησιμοποιώντας Client For NetWare Networks;
    a. Make sure that you are using the correct frame type set in the Advanced properties     for the IPX/SPX-compatible protocol.
    b. Set Bindery Context Parameter by loading the SERVMAN NetWare module.
  58. Τι πρέπει να κάνουμε προκειμένου τα Windows 95 να μην απαιτούν ένα password για την είσοδο σ’αυτά και ένα για το logon στο δίκτυο NetWare;
    If you don’t want to be prompted for a second password, make sure the passwords are the same for both the NetWare preferred server and Windows 95.
  59. Τι ενέργειες πρέπει να κάνουμε προκειμένου να επιτραπεί η πρόσβαση σε ένα NetWare server;
    To see files on NetWare servers for which you have access, synchronize your credentials on all the NetWare servers, using the Novell SETPASS command at the command prompt.
  60. Με ποια εντολή μπορούμε να ελέγξουμε τη version του Novell-supplied software που εκτελείται στον υπολογιστή μας;
    driver_name i or driver_name ?
    π.χ
    netx i
  61. Τι ενέργειες πρέπει να κάνουμε αν αντιμετωπίζουμε προβλήματα με τη χρήση του Novell NetWare Client;
    a. Check the version number of all Novell-supplied NetWare Workstation Shell to make sure that are the latest.
    b. Check for multiple instances of NET.CFG.
    c. Verify that IPXODI is binding to the network adapter by running the Novell NEVER utility. If IPXODI is not bound to the Network adapter, change the entries in NET.CFG to correct this problem.
    d. For a monolithic configuration, verify that the configuration does not use the /o# switch on IPX.COM or the config option = statement in SHELL.CFG.
    e. If the user is running a shared copy of Windows 95, verify that home directory and shared Windows 95 directory are the first two items in the path
  62. Τι κάνουμε αν κατά την διαδικασία του SETUP απαιτείται το Novell Workstation Shell Installation Program;
    Ensure that the correct VLM information is placed in SYSTEM.INI. The Novell-supplied installtion program for VLM sets the path in SYSTEM.INI to the Windows 95 SYSTEM directory rather than to VMM32 directory.
  63. Τι κάνουμε αν μετά την εγκατάσταση των Windows 95 δεν μπορούμε να κα΄νουμε attach σε κάποιο NetWare server;
    Verify the Frame Type being used by Novell NetWare server. Manually edit NET.CFG so that the correct frame type is first in the link driver section.
  64. Τι πρέπει να κάνουμε όταν δεν μπορούμε να δούμε τους άλλους υπολογιστές που τρέχουν Windows 95 ή τον NetWare server;
    a. Determine which frame type is used at your site and then verify that the correct frame type you want to use on Network are listed in NET.CFG.
    b. Verify that the correct NET.CFG is being processed by the LSL.COM
    c. Verify that NET.CFG contains the correct settings for Network adapter.
    d. Verify that you are running the latest version of Novell-supplied ODI drivers and support files.
    e. Verify that both Client computers are running the same protocol.
    f. Verify that an IPX/SPX protocol is installed on both client computers.
  65. Τι κάνουμε όταν δεν μπορούμε να προσπελάσουμε το login drive μετά την εγκατάσταση των Windows 95;
    For a client computer using NETX Workstation Shell, the NetWare login drive is the next drive letter available after the Lastdrive statement in the Registry. You can alter the Lastdrive= statement to change the login drive but you must leave enough drive letters before the Lastdrive= that win use for its own connections.
  66. Πως τα Windows 95 προφυλλάσουν τους άλλους NetWare clients απ’το να νομίζουν ότι ο σταθμός που έχει εγκατεστημένο το File and Printer Sharing είναι ο Novell NetWare server;
    The windows directory contains NWSYSVOL\LOGIN\LOGIN.EXE
  67. Ποιες ενέργειες πρέπει να κάνουμε έτσι ώστε τα Windows 95 να συνεργαστούν σωστά με έναν LANtastic real-mode Network Client;
    a. Make sure that the LANtastic server is not running.
    b. Make sure that the LANtastic client is already installed under MS-DOS, Windows 3.1 or Windows For Workgroups.
    c. Start SETUP.
  68. Τι πρέπει να κάνουμε έτσι ώστε τα Windows 95 να συνεργαστούν με DEC PATHWORKS real-mode client;
    a. In Windows 95 SETUP, choose Custom Setup.
    b. Install Client For Microsoft Networks.
    c. In the Network Configuration dialog box, click Add then double-click Protocol in the Select Network Component Type dialog box.
    d. In the Select Network Protocol dialog box, click Digital Equipment (DEC) in the Manufacturers list, and click DEC PATHWORKS protocol in the Network Protocol list, depending on the server version number whether you are running on token-ring or Ethernet Network. Click OK. Then click Next button to continue SETUP.
  69. Ποια είναι τα πρωτόκολλα που χρησιμοποιούνται για Host Connectivity;
    a. IPX/SPX
    b. NetBEUI
    c. TCP/IP
    d. DLC
  70. Ποιες ενέργειες πρέπει να κάνουμε προκειμένου να εγκαταστήσουμε το Microsoft DLC protocol σε έναν υπολογιστή που τρέχει Windows 95;
    a. In the Network option in Control Panel, click Add.
    b. In the Select Network Component Type dialog box, double click Protocol.
    c. In the Select Network Protocol dialog box, click Microsoft in the Manufacturers list, and then click Microsoft DLC in the Protocols list. Then click OK.
    d. Shut down and restart the computer for changes to take effect.
    e. Make sure that there is only one Net start entry in AUTOEXEC.BAT because SETUP automatically adds an entry to support DLC even if such already exists.
  71. Ποιες ενέργειες πρέπει να κάνουμε προκειμένου να λύσουμε προβλήματα που τυχόν αντιμετωπίζουμε με τη χρήση του Microsoft DLC protocol;
    a. Make sure that only one Net start entry in AUTOEXEC.BAT.
    b. Do not make direct changes to PROTOCOL.INI.
    c. Same terminal applications use TSR’s to communicate with Microsoft DLC protocol. Make sure that the entry for the TSR is still in AUTOEXEC.BAT.
    d. The option named Set This Protocol To Be The Default Protocol, must be unchecked, because Microsoft DLC does not use LANA settings.
    e. Real-mode Microsoft DLC is an NDIS 2 protocol, so the Network adapter must have an NDIS 2-compatible Network adapter driver for use with Windows 95.
  72. Ποια είναι τα πλεονεκτήματα από την χρήση του Network Neighborhood;
    a. Users can browse the Network as easily as browsing the local hard disk.
    b. Users can create shortcuts to Network resources on the desktop.
    c. Users can easily connect to Network resources by clicking the Map Network Drive button that appears on most toolbars.
    d. Users can open files and complete other actions by using common dialog boxes in applications.
    e. The Network Administrator can customize Network Neighborhood by using system policies.
  73. Ποια είναι τα πλεονεκτήματα από την χρήση του File and Printer Sharing for NetWare Networks σε ένα NetWare Network;
    a. Users can share files, printers, and CD-ROM drives without running two Network Clients.
    b. Security is user-based NOT share-based. You can administer user accounts, passwords and group lists in one place on the NetWare server.
    c. Users running VLM or NETX clients can access shared resources on computers running Windows 95.
    d. You can add secure storage space and printing to the Network inexpensively while using familiar NetWare tools to manage these resources.
    e. You get a scalable, high performance 32bit peer server that uses multiple 32bit threads, the new Windows 95 FAT 32bit File System, 32 bit NDIS drivers, 32bit IPX/SPX-compatible protocol and burst-mode protocol.
  74. Ποιες προϋποθέσεις πρέπει να ισχύουν για να μπορέσει ο browser των Windows 95 να προβάλει TCP/IP subnetworks;
    To take advantage of this, the Network must use a WINS server or you must use #DOM entries in LMHOSTS files for name resolution.
  75. Με ποιο τρόπο μπορούμε να κάνουμε attach σε έναν NetWare server μέσω του Network Neighborhood;
    a. In the Network Neighborhood, right click a NetWare server.
    b. In the context menu, click Attach As. Then type a user name and a password and click OK.
    c. If you want to map a directory on this server, double click the server icon, right click the directory icon and click Map Network Drive in the context menu.
  76. Περιγράψτε τις ρυθμίσεις του Browse Master.
    a. In the Network option in Control Panel, double-click File And Print Sharing For Microsoft Networks in the list of installed components.
    b. In Advanced properties for File And Printer Sharing for Microsoft Networks select Browse Master in Property list.
    c. Select an option in the Value list as described in the following table:
    Automatic = Specifies that this computer will maintain the browse list if Windows 95 determines that it is necessary. (Default)
    Yes = Specifies that this computer is to be used to maintain the browse list for computers in this workgroup.
    No = Specifies that this computer is never used to maintain the browse list.
    d. At least one computer in the workgroup must have the values of Automatic or Yes.